Unexpected error when restoring the system 0xc0000022: how to fix the situation?
Probably, it is not necessary to say that very manyusers of computers and laptops running Windows operating systems, sometimes (and quite often) after critical failures have to deal with their rollback (recovery from a control point of the previous state). But the trouble is, many people are shocked by the appearance of the message "an unexpected error when restoring the system 0xc0000022". What to do, after all it turns out that it is impossible to roll back the system? Not surprisingly, some users who do not know how to fix this situation immediately try to reinstall Windows. This is just not worth doing. You can do less drastic methods. This requires only a "native" boot disk system or something like a Live CD.
Unexpected error when restoring the system 0xc0000022: what is this?
To begin with, we will focus on the failure itself. Many people are wondering why, when setting the rollback at the boot stage, an unexpected error occurs when restoring the system to 0xc0000022. Windows 7, such a beloved, not the only system in which such a glitch may manifest itself. In the G8 and the Tenth, this phenomenon is also not uncommon.
In general, if we consider the root causes, whenthe system displays a message that an unexpected error occurred while restoring the system 0xc0000022, basically there are two main points: the consequences of viruses and the absence or damage of some system components responsible for the rollback of the system. We will analyze both situations.
As follows from the foregoing, recovery is notIt works, and as a result, the system can not boot even in a safe mode. To begin with, it is recommended to perform a comprehensive computer system check for viruses that could lead to such a situation.
It goes without saying that a regular scannernot available. In this case, you should use special utilities with the general name Rescue Disk, recorded on an optical disk or USB-media, which load their own interface and the most necessary software components even before the start of Windows. If viruses are not detected during the scanning process, and the system with obvious persistence will again display a message that an unexpected error occurred while restoring the system 0xc0000022, proceed to the following steps. To boot, we now use the above mentioned disks (either the installation CD with Windows, or Live CD).
Unexpected error when restoring the system 0xc0000022: how to fix it by the simplest method?
So, start with a disk or a flash drive, after which, toFor example, in the case of the "native" Windows disk, we do not install the system, but go to the Recovery Console. In principle, you can try to roll back the system from the corresponding section, but, as practice shows, this will lead to nothing, and the message "Unexpected error when restoring the system 0xc0000022" will appear again. Unsurprisingly, because all data about the rollback point and the saved parameters are not on the optical or USB-drive, but on the hard disk of a computer or laptop.
Here comes the help of the command line. You can call it from the console menu or use the Shift + F10 keys. Now in the appeared window you need to register the command sfc / scannow and press the enter key. Further, the verification process is activated, during which critical components of the system, including those responsible for rolling back, will be restored.
Specific methods for damage to the boot record
If the previous method did not give the result, it seems that the user was confronted with the fact that the main boot record was corrupted in the system. It will have to be restored.
Repeat all the actions for downloading and againwe reach the command line. Here we assign the following commands: first Bootrec.exe / FixMbr, and then - Bootrec.exe / FixBoot. In most cases, no additional action is required. After successfully executing them, as the message on the screen will indicate, you can try to restart the system again. In this case, if the recovery is not activated automatically, you need to reboot with the Safe Mode menu call, which uses the boot line of the last successful configuration.
If this does not work, we repeat all the actions,described above, and to the two previous commands we add one more: Bootrec.exe / RebuildBcd (it overwrites the boot sector). After performing this operation, everything should be done without problems.
It remains to add that here we have consideredonly the most effective methods that require the use of the command line and boot disk. Of course, you can try to remedy the situation and with the help of special utilities designed for the fact that the rollback was started directly by means of running Windows, when for some reason the recovery turned out to be impossible, but the system still at least somehow, but is loaded. In our case, the technique is designed exclusively for those situations when the system does not work at all. By the way, the above methods make it possible to restore the system's efficiency not only when such a failure occurs, but in many other cases it is a truly universal solution, and not dependent on the presence of stored control points. They can be used only when Windows starts working again.